When you see the lightning bolt symbol appear on your 2006 Dodge Charger, it’s an indication that your gas pedal and your electronic throttle control are failing to communicate. There are several factors that can cause this issue to occur, including: Failing EGR valve.
Considering this, Can you drive with electronic throttle control light on? It is not safe to drive with an electronic throttle control light. While you might be lucky and only have a drop in fuel efficiency or a slight drop in acceleration, the problem can quickly get worse if the sensor readings continue to go awry.
How do I fix my electronic throttle control light?
solution: stop driving your vehicle and have it towed to your mechanic. there, the first step will be to scan the engine computer for a trouble code. this should point your mechanic in the right direction. if there is no code, then a check of the sensors, relays, and wiring in the system should identify the problem.
Correspondingly, What does the lightning bolt mean when charging? What does the battery symbol with a lightning bolt through it mean? The lightning bolt across the battery icon on the main menu screen means that the device is plugged into an external power source. If you remove the device from the power source the lightning bolt will disappear, leaving only the battery icon.
Then, What does the lightning bolt mean on a 2010 Dodge Charger? The lightning bolt icon on your dashboard alerts you to a problem with the electronic throttle control system.is the check engine light or service engine soon light on? Byron79 on February 29, 2016. No. stevieray1 on February 29, 2016. the light is throttle issues, stuck, gummy, etc.
What does service electronic throttle control mean?
Electronic throttle control (ETC) is an automobile technology which electronically « connects » the accelerator pedal to the throttle, replacing a mechanical linkage.
How do you reset the throttle on a Dodge Charger?
Throttle calibration can take care of these.
- Insert ignition key and turn to « ON » (not start).
- Wait for all idiot lights to go out. …
- Slowly depress the accelerator pedal all the way to the floor.
- Slowly release the accelerator pedal until it’s all the way back up.
- Turn the ignition key to « OFF ».
How do I reset my Dodge Charger?
Press the gas pedal ALL the way down slowly and all the way back up slowly (process of all the way down and back up should take about 10 seconds). Press the ignition switch once to put it back to off and viola. Start the car normally. That should do it.
What does the lightning bolt mean on a 2012 Dodge Charger?
Instead, a sensor monitors the position of the pedal and that information is sent to the ETC to make changes in engine speed. If the system detects a problem that results in an ETC error, the ETC light illuminates on the dashboard.
How do you reset the throttle control on a Dodge?
To reset the system all You need to do is turn on the vehicle without starting the engine. After that You can just press down on the throttle pedal for ten seconds and wait until the engine light starts to blink. When that happens it is resetting the throttle body and the ECU’s memory.
How much does it cost to fix electronic throttle control?
If it’s the electronic throttle controller then the replacement cost can range from $300 to $1,500 depending on the location and time to complete the job. If it’s the throttle body itself that is damaged and needs to be replaced, the costs can also be in the same neighborhood.
How do you fix the electronic throttle control on a 5.7 L Hemi?
Most effective ways to fix the Electronic Throttle Control 5.7L Hemi
- Cleaning the throttle body.
- Changing the hose.
- Resetting the throttle system.
- Replacing the throttle system.
How much does it cost to fix the electronic throttle control on a 2008 Dodge Charger?
The average cost for a Dodge Charger throttle body replacement is between $439 and $449. Labor costs are estimated between $35 and $44 while parts are priced at $404. This range does not include taxes and fees, and does not factor in your specific model year or unique location. Related repairs may also be needed.
How do you reset the electronic throttle control on a Dodge Challenger?
How do I reset my throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do I get my Dodge Charger out of limp mode?
In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps:
- Stop the vehicle.
- Shift the transmission into PARK.
- Turn the engine OFF.
- Wait approximately 10 seconds.
- Restart the engine.
- Shift into the desired gear range.
How do I reset my Dodge computer?
To turn it off, you’ll need to reset the computer.
…
Turning Off the RAM 1500 Check Engine Light
- Identify your battery’s negative cable.
- Disconnect the negative cable from the battery.
- Wait 20 minutes so that all systems have shut down.
- Reconnect the negative cable.
How do you clear the codes on a Dodge Charger?
Simply turn on the ignition and off the components. The engine’s error codes can be accessed by typing “Read” into your scan tool… By pressing “Erase,” the error code will be cleared and you will no longer need to run the software on your scanner.
What does the lightning bolt mean on a 2009 Dodge Charger?
This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running. Cycle the ignition key when the vehicle is completely stopped and the gear selector is in the PARK position. The light should turn off.
What does the red lightning bolt mean on 2007 Dodge Charger?
The Red lightning bolt of death means the car’s computer thinks there is no communication between the gas pedal and the throttle bottle. It is called an Electronic Throttle Control, or ETC for short.
Why is my Dodge Charger not starting?
The most common reasons a Dodge Charger won’t start are a dead battery, an alternator problem, or failed starter.
How do you reset the throttle body?
Leave the key off for a moment, turn the key to the « On » position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.
How do you reset a throttle body sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do I reset my accelerator pedal sensor?
To recalibrate the ECM and accelerator pedal, the ignition switch must be in the ON position and then the accelerator pedal must be slowly and fully depressed from idle to full throttle. Repeat the procedure three times.
Can throttle control make car not start?
Yes, a bad throttle body can cause a car not to start, and that is because of two reasons. First, the throttle body is not allowing the right amount of air into the combustion chamber so there is no spark to set off the ignition.
How many hours does it take to replace a throttle body?
How long does a throttle body replacement take? The job usually takes around an hour for either a replacement or a cleaning.
Is it hard to replace a throttle position sensor?
When a throttle position sensor goes bad, your vehicle may stall or run rough at idle, and may stumble upon acceleration. The replacement of the TPS is a straightforward procedure that should take an amateur mechanic less than an hour to complete.
What happens when you unplug throttle position sensor?
If your TPS has become unplugged or is in need of repair, your car will start to accelerate. However, it will only go up to a certain speed. In most cases, it will stay between 20 to 30 MPH. There could likewise be a lack of power that won’t allow you to accelerate.
How do you reset the throttle body on a 2006 Dodge Ram 1500?
For your 2006 Dodge Ram pickup truck, place the ignition in run position without starting, depress the gas pedal and release within 2 seconds (1 up, 1 down). You should hear a confirmation ding if done properly. The throttle control should now be reset — you’ll know when you have open throttle.
How do you reset the electronic throttle control system on a Dodge Durango?
Resetting Your Electronic Throttle Control
- Step 1 – Make sure the accelerator pedal is fully released. …
- Step 2 – Turn the ignition on and then turn it off. …
- Step 3 – Turn the ignition on again for 7 seconds and then press the gas pedal five times before releasing for 5 seconds.
Don’t forget to share this post !
